- #OKIDATA C5800 BELT MISSING 300 ERROR SERIAL#
- #OKIDATA C5800 BELT MISSING 300 ERROR DRIVERS#
- #OKIDATA C5800 BELT MISSING 300 ERROR DRIVER#
- #OKIDATA C5800 BELT MISSING 300 ERROR SOFTWARE#
All the information provided is subject to change from time to time at the sole discretion of Oki Data.Detected an abnormality of internal database.Īfter pressing, the data will be deleted, and then reboot. However, Oki Data assumes no responsibility for errors or omissions which may occur. Oki Data has taken care to insure that the information is complete, accurate and up-to-date. Try moving the paper guides together so that the paper rests on the guides rather than If you have this problem during high-volume printing jobs, Solution: Sometimes static charges can build up on continuous-form paper, making itĬling to the paper separator. Problem: Static electricity causes my continuous-form paper to stick. If the printer is part of a customized system or if it is usedīy a number of people, the system manager may have used this option to make Solution: The Operator Panel Function item on the printer menu can be used toĭisable these buttons. Problem: The menu and print feature buttons on the front panel won't work. Overrides any settings you have made using the front panel. The I-Prime signal is sent over the parallel interface (pin 31) and automatically String may still override the printer menu and/or front panel settings. The reset command from resetting your printer, other commands in the initialization Inhibit item in the General Control group to Yes. Printer to ignore the reset command, enter the printer menu and change the Reset These commands override panel or menu settings. The initialization string contains commands that change the printer to a default Solution: Before sending a file to the printer, many word processors sendĮither an initialization string or an I-Prime signal to the printer. Problem: My word processor files don't print the way I have the menu and (2) If you have embedded any printer commands in your software, check to be sure that you
#OKIDATA C5800 BELT MISSING 300 ERROR DRIVERS#
One of the drivers listed for that emulation in Chapter 4( ).
#OKIDATA C5800 BELT MISSING 300 ERROR SOFTWARE#
If the emulation is correct, check your software to be sure that you have selected Necessary, press the SET button to change the emulation, (e) press the MODE button to exit Make sure paper is loaded, (b) press the MODE button, (c) press the GROUP button, (d) if
#OKIDATA C5800 BELT MISSING 300 ERROR DRIVER#
For the Epson/IBM model, first check the driver selected in the printer menu: (a) Solutions: (1) The printer driver you have selected does not match the emulation selected for Problem: I'm getting strange symbols, incorrect fonts, etc., when I try to print a document. Setting (see Setting the Head Gap( ) in Chapter 1 of this manual). Solution: The head gap may not be set correctly. Problem: There are dots missing in my printouts. If heat continues to increase, the printer stops until the printhead coolsĭown then it automatically resumes printing. When the printhead reaches a certain temperature, the printer switches Solution: This is a feature designed to protect the printhead from overheating when it's been Problem: The printer suddenly changes to unidirectional printing, then stops completely and t If not, it will catch on the bail arm as it advances.
Solution: Be sure to set the top of form so that the paper is held in place by the bail arm The paper should now feed to the proper position. Paper then, after making sure the ALARM light is on, press the TOF/QUIET button to reset Solution: You need to reset the top of form: first press the FORM FEED button to eject the Problem: When using single-sheet paper, the sheet feeds to a position where the top of form
#OKIDATA C5800 BELT MISSING 300 ERROR SERIAL#
(3) If you have installed the serial I/F board, check to be sure that the board is firmly seated in (2) The printer cable may be loose: check the cable to be sure that it is securely connected both If the SEL light is out, press the SEL button to Solutions: (1) The printer may be deselected. Problem: The printer doesn't print when the computer sends data. The ALARM light doesn't go out when you reload paper, call for service. Go out if you're out of paper: be sure to press the SEL button after you've reloaded paper.
To the right and is not covering the groove at the left end of the platen. Solution: The printer is out of paper, the paper has jammed, or the paper is installed too far If you're using a power strip, make sure it's turned on. Check the power cord connection to the outletĪnd to your printer. Solution: The printer may not be plugged in. Problem: Nothing happens when I turn on the printer.
0 kommentar(er)
